Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Ono, Ayako; Yamashita, Susumu; Sakashita, Hiroto*; Suzuki, Takayuki*; Yoshida, Hiroyuki
Dai-26-Kai Doryoku, Enerugi Gijutsu Shimpojiumu Koen Rombunshu (Internet), 4 Pages, 2022/07
JAEA is implementing a simulation of a two-phase flow in the reactor core by TPFIT and JUPITER which are developed by JAEA based on the surface tracking method. However, it is impossible to simulate a boiling on the heating surface in the large-scale domain by this type of simulation method since the simulation of boiling based on the surface tracking method needs the fine mesh which sufficiently resolves the initiation of boiling. Therefore, JAEA started to develop the simplified boiling model applied for the two-phase flow in the fuel assemblies. In this study, the simulation results of the convection boiling on a vertical heating surface and the comparison between the simulation results and experimental results are shown.
Imaizumi, Yuya; Aoyagi, Mitsuhiro; Kamiyama, Kenji; Matsuba, Kenichi; Akayev, A. S.*; Mikisha, A. V.*; Baklanov, V. V.*; Vurim, A. D.*
Dai-26-Kai Doryoku, Enerugi Gijutsu Shimpojiumu Koen Rombunshu (Internet), 4 Pages, 2022/07
The cooling of the residual core materials after the fuel discharge from the SFR core in the core disruptive accident can significantly affect the distribution fraction of the core materials which is an important factor for the in-vessel retention (IVR). The cooling of the residual core materials is called "in-place cooling". For the evaluation of the in-place cooling, behavior in a SFR core was simulated by SIMMER-III, and method of phenomena identification and ranking table (PIRT) was applied based on the analysis result. Experiment which focuses on the thermal-hydraulic phenomena which were extracted by the PIRT was conducted in the framework of EAGLE-3 project. Continuous oscillation of sodium level which can occur in the phase of in-place cooling of SFRs was observed in the experiment, and analysis by the SIMMER-III was conducted. By investigation of the analysis result, difference between the experiment and analysis results was revealed to be due to remaining and occupation of non-condensable gas above the sodium level which would be unrealistic in the experiment. Gas mixture model between non-condensable gas and sodium vapor was developed to solve this problem, and coincidence between experiment and analysis results was largely improved by this new model.
Emura, Yuki; Kamiyama, Kenji; Yamano, Hidemasa
Dai-26-Kai Doryoku, Enerugi Gijutsu Shimpojiumu Koen Rombunshu (Internet), 4 Pages, 2022/07
no abstracts in English
Kikuchi, Norihiro; Mori, Takero; Okajima, Satoshi; Tanaka, Masaaki; Miyazaki, Masashi
Dai-26-Kai Doryoku, Enerugi Gijutsu Shimpojiumu Koen Rombunshu (Internet), 5 Pages, 2022/07
In JAEA, the design optimization method for plant structure has been developed on the process to output optimal solution of the thickness of reactor vessel wall against thermal transient and seismic loads in a SFR as a representative problem. Resistance characteristic of the wall on the load derived from thermal transient is one of the most important factors for safety estimation on the structural integrity. Failure probability of components against thermal transient was set to one of variables in the objective function for a common scale to compare with other variables in different failure mechanisms. In the iterative process to achieve the optimal solution, a number of evaluations to measure the influence on the load derived from thermal transient was necessarily conducted. More reduction of required time for evaluations is desired. To perform the iterative evaluation process efficiently, the automatization of parametric analyses was implemented in the optimization process.
Li, C.-Y.; Watanabe, Akira*; Uchibori, Akihiro; Okano, Yasushi
Dai-26-Kai Doryoku, Enerugi Gijutsu Shimpojiumu Koen Rombunshu (Internet), 4 Pages, 2022/07
Identifying accident scenarios that could lead to severe accidents and evaluating their frequency of occurrence are essential issues. This study aims to establish the methodology of the dynamic Probabilistic Risk Assessment (PRA) for sodium-cooled fast reactors that can consider the time dependency and the interdependence of each event. Specifically, the Continuous Markov chain Monte Carlo (CMMC) method is newly applied to the SPECTRA code, which analyzes the severe accident conditions of nuclear reactors, to develop an evaluation methodology for typical external hazards. Currently, a fault-tree model of air coolers of decay heat removal system is implemented as the CMMC method, and a series of preliminary analysis of the plant's transient characteristics under the scenario of volcanic ashfall has been conducted.
Tanaka, Masaaki; Doda, Norihiro; Yokoyama, Kenji; Mori, Takero; Okajima, Satoshi; Hashidate, Ryuta; Yada, Hiroki; Oki, Shigeo; Miyazaki, Masashi; Takaya, Shigeru
Dai-26-Kai Doryoku, Enerugi Gijutsu Shimpojiumu Koen Rombunshu (Internet), 5 Pages, 2022/07
To assist conceptual studies of various reactor systems conducted by private sectors in nuclear power innovation, development of an innovative design system named ARKADIA (Advanced Reactor Knowledge- and AI-aided Design Integration Approach through the whole plant lifecycle) is undergoing to achieve the design of an advanced nuclear reactor as a safe, economic, and sustainable carbon-free energy source. In this paper, focusing on the ARKADIA-Design as a part of it, the progress in the development of optimization processes on the representative problems in the fields of the core design, the plant structure design, and the maintenance schedule planning are introduced.
